Rigol DP832 User Manual Page 89
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2 Front Panel Operations RIGOL
DP800 User’s Guide 2-39
or "Output Toggle".
Output On: when the trigger condition is met, turn on the output of the
channel currently selected as the source under control.
Output Off: when the trigger condition is met, turn off the output of the
channel currently selected as the source under control.
Output Toggle: when the trigger condition is met, turn the waveform of the
channel currently selected as the source under control upside down and
then output the waveform.
5. Sensitivity
Press Sensitivity to set the sensitivity to high, middle or low. Selecting
relatively lower trigger sensitivity can avoid mis-trigger at the noise.
6. Enable
Press Enable to enable or disable the trigger input function of the
corresponding data line.
Trigger Output
When the output of the specified control source meets the trigger condition, the
specified data line outputs level or square waveform according to the setting of the
output signal.
Press Trigger Trig to select "Out" and the trigger output setting
interface is opened, as shown in the figure below.
Figure 2-7 Trigger Output Setting Interface
1. Data Line
Press Data Line to select D0, D1, D2 or D3 and the data line currently selected
will be highlighted on the screen. Users can set the trigger conditions of the four
data lines respectively.
2. Control Source
Press Ctrl Src to select any of CH1, CH2 and CH3 as the control source.
- User’s Guide 1
- DP800 Series Programmable 1
- Linear DC Power Supply 1
- Guaranty and Declaration 3
- Safety Requirement 4
- DP800 User’s Guide III 5
- Safety Terms and Symbols 6
- DP800 User’s Guide V 7
- RIGOL 8
- VI DP800 User’s Guide 8
- General Care and Cleaning 10
- Environmental Considerations 11
- DP800 Series Overview 12
- RIGOL 13
- DP800 User’s Guide XI 13
- Document Overview 14
- DP800 User’s Guide XIII 15
- Contents 16
- Contents RIGOL 17
- DP800 User’s Guide XV 17
- Chapter 1 Quick Start 19
- General Inspection 20
- Appearance and Dimensions 21
- Front Panel 22
- Chapter 1 Quick Start RIGOL 23
- DP800 User’s Guide 1-5 23
- RIGOL Chapter 1 Quick Start 24
- 1-6 DP800 User’s Guide 24
- DP800 User’s Guide 1-7 25
- 8V/10A60V/1A 26
- DP800 User’s Guide 1-9 27
- 1-10 DP800 User’s Guide 28
- Opt. Opt 29
- 1-12 DP800 User’s Guide 30
- To Connect to Power 31
- Power-on Inspection 32
- To Replace the Fuse 32
- DP800 User’s Guide 1-15 33
- User Interface 34
- DP800 User’s Guide 1-17 35
- 1-18 DP800 User’s Guide 36
- To Rack Mount the Instrument 37
- Installation Tool 38
- Installation Space 38
- Installation Procedures 39
- 1-22 DP800 User’s Guide 40
- DP800 User’s Guide 1-23 41
- 1-24 DP800 User’s Guide 42
- DP800 User’s Guide 1-25 43
- To Install Two Instruments 44
- DP800 User’s Guide 1-29 47
- Instrument A Instrument B 47
- 1-30 DP800 User’s Guide 48
- DP800 User’s Guide 1-31 49
- 1-32 DP800 User’s Guide 50
- DP800 User’s Guide 2-1 51
- Constant Voltage Output 52
- DP800 User’s Guide 2-3 53
- DP800 User’s Guide 2-5 55
- Constant Current Output 56
- DP800 User’s Guide 2-7 57
- 2-8 DP800 User’s Guide 58
- DP800 User’s Guide 2-9 59
- Track Function 60
- DP800 User’s Guide 2-11 61
- 2-12 DP800 User’s Guide 62
- Sense Working Mode 63
- Timer and Delayer 65
- To Set the Timer Parameters 66
- To Set the Number of Cycles 67
- To Set the End State 67
- To Edit the Timer Parameters 67
- 2-18 DP800 User’s Guide 68
- DP800 User’s Guide 2-19 69
- Symmetry=t/T*100% 70
- -i*RiseIndex/P 71
- -i*FallIndex/P 72
- DP800 User’s Guide 2-23 73
- 2-24 DP800 User’s Guide 74
- To Enable the Timer 75
- To Set the Delay Parameters 76
- To Edit the Delay Parameters 77
- 2-28 DP800 User’s Guide 78
- To Set the Stop Condition 79
- To Enable the Delayer 80
- Advanced Functions 81
- Recorder 82
- Analyzer (option) 83
- 2-34 DP800 User’s Guide 84
- DP800 User’s Guide 2-35 85
- Monitor (option) 86
- Trigger (option) 87
- Trigger Input 88
- Trigger Output 89
- 2-40 DP800 User’s Guide 90
- Display Setting 91
- Display Mode 92
- Display Theme 92
- DP800 User’s Guide 2-43 93
- 2-44 DP800 User’s Guide 94
- Store and Recall 95
- Browser 96
- File Type 96
- DP800 User’s Guide 2-47 97
- 2-48 DP800 User’s Guide 98
- DP800 User’s Guide 2-49 99
- Copy and Paste 100
- Utility 101
- I/O Configuration 102
- DP800 User’s Guide 2-53 103
- 2-54 DP800 User’s Guide 104
- DP800 User’s Guide 2-55 105
- To Set the RS232 Parameters 106
- To Set the GPIB Address 107
- System Setting 108
- Keyboard Lock 109
- Track Setting 109
- System Information 110
- System Language 110
- Test/Calibration 110
- DP800 User’s Guide 2-61 111
- Preset Setting 112
- Table 2-2 Factory setting 113
- DP800 User’s Guide 2-67 117
- 2-68 DP800 User’s Guide 118
- Options 119
- 2-70 DP800 User’s Guide 120
- Key Locking 121
- DP800 Programming Guide 123
- Remote Control via USB 124
- DP800 User’s Guide 3-3 125
- 3-4 DP800 User’s Guide 126
- DP800 User’s Guide 3-5 127
- 3-6 DP800 User’s Guide 128
- DP800 User’s Guide 3-7 129
- 3-8 DP800 User’s Guide 130
- DP800 User’s Guide 3-9 131
- 3-10 DP800 User’s Guide 132
- DP800 User’s Guide 3-11 133
- Chapter 4 Troubleshooting 135
- Chapter 5 Specifications 137
- 0.5%+0.5V/0.5%+0.5A 139
- Chapter 6 Appendix 141
- Appendix B: Warranty 142
- Index RIGOL 143
- DP800 User’s Guide 1 143
- RIGOL Index 144
- 2 DP800 User’s Guide 144
Related products and manuals for Generators Rigol DP832
Generators Rigol DSG3000 Series User Manual
(81 pages)
(81 pages)
Generators Rigol DSG3000 Series User Manual
(187 pages)
(187 pages)
© 2020, manymanuals.com. All rights reserved. | 0.930 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals