Rigol DG10X2 Series User's Guide Page 47
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
- Waveform Generator 1
- Safety Notices 4
- Safety Terms and Symbols 5
- Instrument at a Glance 6
- Chapter 5 Specifications 7
- Content 8
- Chapter 1 Quick Start 11
- General Inspection 12
- Handle Adjustment 13
- The Front/Rear Panel 14
- The Rear Panel at a Glance 15
- User Interface 16
- To Set a Waveform 17
- Low level, Symmetry and Phase 18
- Offset/ Low level and Phase 19
- To Set the Output 21
- To Set Modulate/Sweep/Burst 22
- To Use Digital Input 24
- To Set Basic Waveforms 28
- Current Parameter: 29
- Frequency 29
- To Set the Output Amplitude 30
- To Set the Offset 31
- To Set the Initial Phase 32
- To Set Square Waveform 33
- To Set the Duty Cycle 35
- To Set Ramp Waveform 36
- To Set the Symmetry 37
- To Set Pulse Waveform 38
- To Set the Pulse Width 39
- To Set the Pulse Delay 40
- To Set Noise Waveform 41
- To Set Arbitrary Waveforms 42
- To Select Arbitrary Waveform 43
- Figure 2-23 45
- To Edit Arbitrary Waveform 47
- To Create a New Waveform 48
- Default Arbitrary 51
- Waveform 51
- To Edit the Stored Waveform 52
- To Set Modulated Waveforms 53
- To Set AM Waveform 54
- To Set FM Waveform 56
- To Set FSK Waveform 58
- FSK Frequency 59
- Hop Frequency 59
- To Set PM Waveform 60
- To Generate Sweep Signal 62
- Sweep Frequency Setting 63
- To Generate Burst Signal 64
- Set the N-Cycle Burst 65
- Set the Gated Burst 67
- Figure 2-47 67
- To Store and Recall 68
- To Save the Instrument State 69
- To Save Data 70
- To Use USB storage 71
- To Save a File 72
- Figure 2-51 72
- Figure 2-52 73
- Figure 2-53 74
- To Set the Utility Function 75
- To Set the Sync Output 78
- Channel Coupling Settings 83
- To Set the Counter 85
- Auto Measurement Setting 86
- Manual Measurement Setting 86
- System Settings 89
- PP /0.000 VDC 94
- I/O Settings 96
- Test/Cal Settings 97
- To Use the Help System 99
- Chapter 3 Examples 101
- Output from Single Channel 102
- PP Amplitude, 20mVDC 104
- PP” to set the Amplitude as 104
- PP Amplitude, 5mVDC 105
- The operation steps: 106
- The Burst Waveform Output 116
- Figure 3-12 116
- Output from Double Channels 117
- Example for Channel Copy 122
- Prompting Messages 126
- Error Messages 128
- Data Overflow 129
- Troubleshooting 138
- Chapter 5 Specifications 139
- Characteristics 140
- VPP, 100% 141
- PK = 100% modulation 143
- PP to 5 VPP 144
- PP to ± 5 VPP 144
- PP ~ 10VPP) 144
- General Specifications 146
- Chapter 6 Appendix 147
- Appendix B: Warranty 148
- Appendix D: Contact RIGOL 150
Related products and manuals for Power generators Rigol DG10X2 Series
(32 pages)© 2020, manymanuals.com. All rights reserved. | 0.463 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals