Rigol DG10X2 Series User's Guide download pdf (Page 52)

RIGOL

User’s Guide for DG10× 2 Series

2-26

To Edit the Stored Waveform

Press Arb  Edit  Stored, enter the following interface.

Figure 2-33

Select the waveform to edit

Select the desired waveform document to edit, which will be displayed in inverse

color and press Recall to recall and edit it in the Volatile memory. As shown in the

following figures, users can edit the parameters as in need and store it after the

modification.

Figure 2-34

Edit the waveform parameters

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 149 150

Waveform Generator 1
Safety Notices 4
Safety Terms and Symbols 5
Instrument at a Glance 6
Chapter 5 Specifications 7
Content 8
Chapter 1 Quick Start 11
General Inspection 12
Handle Adjustment 13
The Front/Rear Panel 14
The Rear Panel at a Glance 15
User Interface 16
To Set a Waveform 17
Low level, Symmetry and Phase 18
Offset/ Low level and Phase 19
To Set the Output 21
To Set Modulate/Sweep/Burst 22
To Use Digital Input 24
To Set Basic Waveforms 28
Current Parameter: 29
Frequency 29
To Set the Output Amplitude 30
To Set the Offset 31
To Set the Initial Phase 32
To Set Square Waveform 33
To Set the Duty Cycle 35
To Set Ramp Waveform 36
To Set the Symmetry 37
To Set Pulse Waveform 38
To Set the Pulse Width 39
To Set the Pulse Delay 40
To Set Noise Waveform 41
To Set Arbitrary Waveforms 42
To Select Arbitrary Waveform 43
Figure 2-23 45
To Edit Arbitrary Waveform 47
To Create a New Waveform 48
Default Arbitrary 51
Waveform 51
To Edit the Stored Waveform 52
To Set Modulated Waveforms 53
To Set AM Waveform 54
To Set FM Waveform 56
To Set FSK Waveform 58
FSK Frequency 59
Hop Frequency 59
To Set PM Waveform 60
To Generate Sweep Signal 62
Sweep Frequency Setting 63
To Generate Burst Signal 64
Set the N-Cycle Burst 65
Set the Gated Burst 67
Figure 2-47 67
To Store and Recall 68
To Save the Instrument State 69
To Save Data 70
To Use USB storage 71
To Save a File 72
Figure 2-51 72
Figure 2-52 73
Figure 2-53 74
To Set the Utility Function 75
To Set the Sync Output 78
Channel Coupling Settings 83
To Set the Counter 85
Auto Measurement Setting 86
Manual Measurement Setting 86
System Settings 89
PP /0.000 VDC 94
I/O Settings 96
Test/Cal Settings 97
To Use the Help System 99
Chapter 3 Examples 101
Output from Single Channel 102
PP Amplitude, 20mVDC 104
PP” to set the Amplitude as 104
PP Amplitude, 5mVDC 105
The operation steps: 106
The Burst Waveform Output 116
Figure 3-12 116
Output from Double Channels 117
Example for Channel Copy 122
Prompting Messages 126
Error Messages 128
Data Overflow 129
Troubleshooting 138
Chapter 5 Specifications 139
Characteristics 140
VPP, 100% 141
PK = 100% modulation 143
PP to 5 VPP 144
PP to ± 5 VPP 144
PP ~ 10VPP) 144
General Specifications 146
Chapter 6 Appendix 147
Appendix B: Warranty 148
Appendix D: Contact RIGOL 150

Comments to this Manuals

No comments

Rigol DG10X2 Series User's Guide Page 52

Comments to this Manuals

Related products and manuals for Power generators Rigol DG10X2 Series